Original Publish Date : 5/6/2008
“Dad, Can I Take the Car for a Swim?”
If you love fresh seafood and own a wet suit, the sQuba could be the perfect car for you.

Swiss automotive designer and James Bond-enthusiast Frank Rinderknecht designed and built the submersible sQuba, similar to the fictional car driven by Roger Moore in The Spy Who Loved Me (1977). The biggest challenge, says Rinderknecht, was designing a car that moves like a fish.

Unlike some military vehicles that drive slowly over submerged terrain, the sQuba flies beneath the surface. “We could have designed for greater depths,” says Rinderknecht, CEO of Rinspeed Inc. “But what for? Visibility gets worse with increasing depth, and passengers would need to decompress.” At about 23 ft, a safety switch cuts off all systems. The sQuba then surfaces, or restarts at a lesser depth. The vehicle must move continuously or it will automatically surface.

Rinspeed chose Swiss engineering specialist Esoro to convert a 2008 Lotus Elite into the sQuba. The Lotus was picked for its open roof, small size, light weight, and good looks. The first step was replacing the engine with three electric motors in the rear. One propels the car on land. The other two — supported by jet drives in front — drive the screws. Louvers open and close to control water intake. The jets are made from lightweight carbon nanotubes.

The sQuba floats when driven into water. But cracking open a door floods it in about 10 sec. After another 10 sec, it submerges and accelerates. The passengers breathe compressed air stored in tanks in the trunk. After surfacing, heavy-duty bilge pumps drain the interior.

The open-cabin lets occupants exit quickly in emergencies. Besides, if there were a pressurized cabin, the car would have to weigh 2 tons more to counteract the buoyancy.

Foot pedals control water jets on either side of the car. The left pedal controls the left Seabob jet and the right pedal controls the right one. Two levers replace the normal gearshift and control the angle of the jets. Pushing the levers forward takes the car down, while pulling back brings it up. Controls on the driver’s-side door operate the rear propellers, which turn the car left or right.

Power comes from watertight, rechargeable lithium-ion batteries. All high-voltage components are sealed in a pressuretight box. Underwater, the sQuba will run for about 3 hr, in either fresh or saltwater.

Back on shore, the driver only has to push a button to send power to the rear wheels. Range is about 50 miles at 50 mph. Laser sensors let the car steer itself. Ibeo LUX laser scanners serve as intelligent eyes that guide the vehicle through traffic. On terra firma, the car relies on stainless coil-over suspension, but it’s more at home in the water.

In a nod to 007’s revolving license plate, the rear display changes from “Zero Emission” to “sQuba” in underwater mode.

Make Contact
Rinspeed Inc., rinspeed.com

Click on any of the images below for a full-size view :

Rate / Comment on this Article

Post a comment

Be the first to comment on this article

Login to post a comment
Ultra-Thin Imagers
In Part 2 of Engineering TV's interview with Eric Tremblay, researcher at the UCSD Jacobs School of Engineering, Eric discusses the Montage, a new camera design derived from a "slice" of the original full aperture symmetric lens, which features a much greater depth of field and a USB interface, all in a package about the size of a domino. "This type of miniature camera is very promising...
Origami Optics
Most camera lenses refract light, leading to the familiar cylindrical tube geometry. In some cases, where extended focal length or reduced track length are required, concentric mirrors can be used to effectively reduce barrel length. Recent advances in diamond machining and image processing make it possible to take this approach to a new extreme. With up to 8 reflections, large ray angles, and...
PT-50 Turboshaft Engine
The Turbine Technologies PT-50 turboshaft engine offers a new heavy fuel solution for UAV’s requiring a 50 HP class engine. With its minimal volume and a complete flight ready weight of only 30.6 pounds, the engine exhibits excellent power density. The free power turbine design entails three primary sections: a gasifier core, an accessory section and a power module. The gasifier core contains a...
Aerospace Engineering Controls Lab
The aerospace engineering and engineering mechanicals undergraduate controls laboratory at the University of Texas, Austin, is open to juniors and seniors who have completed a feedback controls systems course and are ready to apply their understanding of classical and state space control theory in the lab. University of Texas Lecturer and Principle Engineer of Controls and Simulation at National Instruments,...
Inkjet Material Deposition System
The MDS 300 is an ultra high precision Materials Deposition System. It enables digital deposition of a wide range of fluids utilizing inkjet printhead technology. The MDS 300 allows the ultimate flexibility in printing capabilities. Users can input print resolution, print speed, printhead separation and curing processes. It can be utilized in both R&D and pilot line production applications....
The blame game
I feel there was a glaring omission in Mr. Berke's May 25, 2006 column titled "For lack of a guard, a severed hand" — personal responsibility.
Shake, rattle, and modal analysis
FEA can be a useful tool for sizing up resonance problems.
Biomimetics could hold a key to next-generation body armor
Who would have thought that your wife's jewelry holds the secret to better body armor?
What's a mechatronics technician?
When Keith Campbell muses about industrial education, his thoughts go back to his uncle Ralph.
The meaning of bearing life
How long will a bearing last? Standardized life equations help to answer.
Engineering an ad
How do you convince a doubting public your truck is tough? You show them.
Tricked-Out Trucks
Stylists and engineers are exploring new ways to personalize pickup trucks, the best-selling type of vehicle in the U.S.
Tom-Thumb turbines power radio-controlled jets
Engineers have managed to shrink the modern jet engine until it is small enough to fit in model planes.
Engineering in India
Here’s a snapshot of the Indian engineers who increasingly compete for global manufacturing work.
Gulliver's Engines
Shrinking full-scale engines to pocket size is no small feat.
PRODUCT SEARCH
Powered by
SEARCH THE PLASTICS WEB™
Powered by
FORUMS
Hydraulic Pump design
Hi, Specify Gear , Vane Piston or others. Nahum Goldenberg info@hydrocad.com

Mass-Transit Myths
It should be noted, Hong Kong = very high population density, very high job density. So not a surprise that mass transit is very convenient there.

What’s Tough About Training
This issue’s emphasis on motion control prompts some reflection on how people learn about motion technology. Often theoretical training isn’t...

What’s hot? Not ethanol
This special issue looks at some of the technologies and industrial themes that are eliciting a lot of interest in the technical community. But...

We Don’t Know How to Recreate Silicon Valley
Preseason football is on TV, the kids are getting ready for the school year, and theme parks are anticipating their final Labor Day crowds. It...